| Manufacturer |
John Deere |
| Price |
17,278(USD) |
| Model |
3025D |
| Equipment Type |
Compact Tractors |
| Factory |
None |
KEY SPECS
| Engine power (gross) |
18.2 kW/24.4 hp |
| Power take-off (PTO) power |
15.4 kW/20.7 hp |
| Steering hydraulics |
14.4 L/min/3.8 gpm |
| Implement hydraulics |
19.2 L/min/5.1 gpm |
| Hitch type |
Category 1 |
| Lift capacity, 24-in. behind link arms |
944 kg/2081.2 lb |
| Standard transmission; forward/reverse |
8F/8R synchromesh shuttle shift gear transmission |
| Cruise control |
No |
| Approximate shipping weight (open-station; cab) |
Open operator station (OOS): 1260 kg/2778 lb/Cab: Not applicable |
| Wheelbase |
1574 mm/62 in. |
ENGINE
The John Deere 3025D is powered by a Yanmar® 3TNV88F-EPJPT engine, delivering 24.4 hp at 2400 rpm with a Final Tier 4 emissions compliance, making it ideal for environmentally sensitive regulations. Its 15.4 kW PTO power allows effective utility for implements, while the pressurized lubrication and liquid cooling systems promote engine longevity under continuous operation. While its three-cylinder design offers a compact engine footprint, users should note the potential challenges of higher maintenance requirements associated with a dual-element air cleaner in dusty environments.
| Manufacturer |
Yanmar® |
| Engine model |
3TNV88F-EPJPT |
| Engine power (gross) |
18.2 kW/24.4 hp |
| Power take-off (PTO) power |
15.4 kW/20.7 hp |
| Rated engine speed |
2400 rpm |
| Injection pump type |
Direct injection |
| Aspiration |
Natural |
| Emissions compliance |
Final Tier 4 |
| Cylinders/displacement |
3 / 1.64 L/3 / 100.2 cu in. |
| Number of cylinders |
Three |
| Cylinder liners |
Cast-in-block |
| Bore and stroke |
88 x 90 mm/3.46 x 3.54 in. |
| Compression ratio |
19.1:1 |
| Lubrication |
Pressurized |
| Cooling system |
Liquid |
| Air cleaner |
Dual element |
| Engine torque at rated speed |
72.4 Nm/53.4 lb-ft |
| Fuel tank capacity |
36.7 L/9.7 U.S. gal. |
ELECTRICAL
| Battery size |
600 CCA |
| Alternator (12-V) |
55 amp |
| Starter size |
1.4 kW/1.9 hp |
FUEL SYSTEM
| Type |
Direct injection |
| Fuel consumption |
/ |
TRANSMISSION
The John Deere 3025D features an 8F/8R synchromesh shuttle transmission, providing smooth forward and reverse shifts, which is advantageous for tasks requiring frequent directional changes, enhancing operator efficiency. Its wet disk brakes and power steering improve safety and maneuverability, especially in tight spaces or uneven terrain. However, the absence of a creeper gear may limit low-speed operation for certain precision tasks, necessitating careful speed management during intricate agricultural operations.
| Standard transmission; forward/reverse |
8F/8R synchromesh shuttle shift gear transmission |
| Left-hand reverser |
Yes |
| Transmission gear ranges |
Four gears and two ranges |
| Final drive |
Spur gear |
| Brakes |
Wet disk |
| Steering |
Power steering |
| Axle capacity |
Front/880 kg/1940 lb/Rear/1600 kg/3527 lb/ |
| Creeper |
No |
| Cruise control |
No |
| Differential lock |
Yes |
HYDRAULICS
| Type |
Open center |
| Pump rated output |
Steering/14.4 L/min/3.8 gpm/Implement/19.2 L/min/5.1 gpm/33.6 L/min/8.9 gpm |
| Pump type |
Single gear |
| Maximum operating pressure |
172 bar/2495 psi |
| Draft control sensing |
Position control |
| Remote control valves available |
Up to two (optional) |
3-POINT HITCH
| Type |
Category 1 |
| Lift capacity, 24-in. behind link arms |
944 kg/2081.2 lb |
POWER TAKE-OFF (PTO)
| Standard |
At 2400 rpm: 540 rpm |
| Control |
Mechanical |
| Clutch |
Transmission |
| Brake (for mid and rear PTO) |
Wet disk |
FLUID CAPACITIES
| Crankcase with filter |
4.5 L/4.8 qt |
| Transmission and hydraulic system |
33 L/34.8 qt |
FINAL DRIVE
OPERATOR STATION
| Rollover protective structure |
Type/Foldable/ASABE S478 |
| Platform - flat/straddle |
Straddle |
| Gear shift location - console/floor |
Right-hand side |
DIMENSIONS
| Wheelbase |
1574 mm/62 in. |
| Front axle clearance |
Minimum: 331 mm/13 in./Maximum: 353 mm/13.9 in. |
| Turning radius with brakes |
1.63 m/5.3 ft |
| Approximate shipping weight (open-station; cab) |
OOS: 1260 kg/2778 lb/Cab: Not applicable |
TIRES
The John Deere 3025D tractor features versatile tire options across three categories: R1 Bar for agricultural performance, R3 Turf for minimal ground disturbance, and R4 Industrial for durability on construction sites. Selecting R1 tires optimizes traction for plowing and tilling, while R3 is ideal for maintaining lawns without damaging the grass. However, R4 tires may face challenges in soft soil conditions, reducing overall traction—balance your choice based on operational needs and terrain.
| Front |
R1 Bar: 7-14/R3 Turf: 27x8.5-15/R4 Industrial: 25x8.5-14 |
| Rear |
R1 Bar: 11.2-24/R3 Turf: 41x14-20/R4 Industrial: 15-19.5 |
MISCELLANEOUS
| Toolbox |
Yes |
| Tilt steering wheel |
No |
| 12-V Outlet |
No |
